How to Crimp a BNC Connector & Make Your Own CCTV Cable.

How to Crimp a BNC Connector & Make Your Own CCTV Cable.


Hello everyone, Matt from satscure.uk here
again. Today I’m going to do a quick video to show you how to make your own CCTV cable.
A lot of cable that you can buy is called pre-terminated cable.
You’ve got a video and a power, and the other end looks like this. Video and power again,
except the power is female on the other end. It’s always best to make your own cable, and
buy a big reel which has better quality copper in that kind of cable. You can see
it’s so thin, and usually the thickness of the cable dictates the quality, and how long
a run you can make using that cable. We usually sell this in 18m reels which works for 2 megapixel cameras,
but it’s always better to make your own cable! So cable on a reel usually looks like this,
so it’s a twin cable, it’s a lot thicker. If you look at the ends here you have one
that’s the power end, and one that’s the video end. The video end is just coax cable. This
cable is called RG59 cable + 2 Core, it’s a bit of a long winded name, but the RG59
part is this part which is for video, and the 2 core part is this bit because its got
2 cores in it! So what you’re going to need is a BNC crimp
tool which look like these, you can usually pick these up for around 20 pounds. These
are an optional extra, this is a coax cable stripper. You can use this for stripping the
shielding off coax cable, or RG59 cable as we are using in this video. You’re going to
need DC male and DC female power ends, which are the power ends for the CCTV. You are also
going to need BNC Crimp connectors which look like this. There’s 3 parts to these. There
are some small parts in them, especially this little bit here. You will have to be careful
not to lose those because they do go walkabout quite easily!
Ill clear the surface and well get started. The first thing we need to do is split the
cable. A lot of the cable that you buy comes like this so you are going to have to pull
it apart to separate the two ends. You want to grab your BNC cable stripper, and it’s
got two ends. This end is quite a lot thinner than this end. So you want to grab the thicker
end first, and you want to score the cable very lightly probably around 2 centimetres
and pull this off, which usually comes off with a little bit of pressure.
So we’ve got here are what a lot of installers call “Short & Curlys”. What we want to do
with those is twist them down and twist them back to the very bottom of the cable so you’ve
got something that looks like this. Then what you want to do is grab a set of
pliers and cut these end bits off quite short and cut them off so you are left with something
that looks like that. Then you want to grab your BNC cable stripper again and go about
5 mil down or at least half way down and cut this bit off so you have something that looks
like that now. Then you want to grab your BNC crimp connector.
Inside a BNC crimp connector we have this bit which is the main connector part, we’ve
got one of these little things which is the bit that you crimp, and we’ve got this tiny
little thing here which is the main connector that connects all the video footage to your
DVR. This bit goes on the end of here, and then you grab your BNC crimp tool.
If you look on your BNC crimp tool you’ve got loads of types of crimp for different
cable types. The one I use mainly is this type here, but here’s a tiny little one which
is used for crimping this tiny little thing onto the cable itself. So I’m just going to
crimp that on… What I also like to do is grab the end and
crimp that right on there. So now that thing is not coming off.
Next thing we want to do is grab our circular bit and slide that over the top of the bit
that we just cut down. This bit then goes on the end, push it right down and you should
hear it CLICK. The connector has just come straight through.
We grab our crimp tool again, this is the final time we will need to use it and just
crimp that onto there and just push it until its really tight. Might want to do it a couple
of times to make sure its properly on. And you should come out of that with a pretty
neat looking connection. That is not coming off now. And that is how
you crimp a BNC connector onto RG59 cable. Next bit we want to do is the 2 core power
cable. Use the cable stripper again, and you can use a Stanley knife if you don’t have
one of these. You can get these for about a fiver but they do come in very useful and
they do last a long time. Similar to what we did last time, you want
to score very lightly around the cable, so now we have a positive and a negative. We
want to expose the copper on the end so I’m going to use the thinner end now.
Positive negative – reddy possy, blacky neggy on the end of our power cable. And now we
want to grab our DC Jack, I’m going to use a male jack for this demonstration. If you
look at the male and female DC jacks they have positive and negative on them, so following
the reddy possy blacky neggy rule which I live my life by we want to stick those into
here and push them right in. So now we have something that looks like that.
Now we grab a tiny little screwdriver and tighten those up.
So now we’ve got a cable that looks like this. And that’s how to crimp a BNC Connector and
make CCTV cable! Thanks a lot guys!

31 Comments

  • m3coo

    June 25, 2017

    thank you sir

    Reply
  • Kabore Karim

    August 13, 2017

    thank you

    Reply
  • Qwqw Bnbn

    August 20, 2017

    You cut all the coax cable copper mash , shouldn't this be connected to the cctv terminal so you would have a ground return and that would reduce any external effects on the quality of the picture?

    Reply
  • THOMAS E B JONES MD

    October 20, 2017

    very nice and very thorough, thank you!

    Reply
  • Abdalla Ahmed

    October 22, 2017

    thanks a lot.

    Reply
  • Alan Brown

    November 25, 2017

    That's about the crappiest BNC crimp job I've ever seen done.

    1: The centre pin MUST butt up against the inner insulation.

    2: NEVER EVER EVER EVER CRIMP THE FERRULE TWICE!!!!! It seriously weakens the ferrule and reduces the crimp pressure. If done properly the metal interfaces will cold-weld themselves into place

    This video is a good example of how NOT to crimp BNC cables.

    Reply
  • swapnildaer

    December 2, 2017

    hello sir
    I'm system integrator in CCTV surveillance
    & I want to buy this product will you suggest me the online supplier

    Reply
  • Sammy Bakar

    December 26, 2017

    That is an incorrect way of terminating the BNC connector. The wire "mesh" or shield should cover the whole back end of the connector and the ferrule goes over the lot for crimping.

    Reply
  • Ognjen Mali

    February 5, 2018

    Satsecure – CCTV • Satellite Stockport
    everything is fine, not to worry about negativity here, some guys are thinking they are the smartests ah. great video,

    Reply
  • sedat aykut

    February 21, 2018

    thank you for the video

    Reply
  • rhaman khalid

    May 17, 2018

    Mate, can i ask a question if possible please, I have messed up my BNC cable when feeding through a external hole, the bnc connector and the power cable have both snapped off, i have watched your video and want to repair it as i have already laid my cctv cable. the only problem i have is with the power cable, when stripping the power cable, i dont have a red and black wire, the two wires are white and exposed copper wire, can you please advise if this is possible to repair and fix ?

    Reply
  • Leslie Slutzkin

    June 1, 2018

    Can we put a link to this video on our website ?

    Reply
  • Yishai Nathan

    June 3, 2018

    omg. i hope u don't crimp professionally. no shielding on your cable. expect interference ! "all the way down" … NOT.

    Reply
  • Yishai Nathan

    June 3, 2018

    "right in" god, so it clamps on the plastic. lol

    Reply
  • itoosh

    June 14, 2018

    Is this crimper works also on RCA cables?

    Reply
  • Daniel Morgan

    June 24, 2018

    Where is your crimper from? Please can you send me a link?

    Reply
  • Charles Smith

    July 8, 2018

    This cam has 3 wires. What are red, black, blue for?

    Reply
  • Juerray Grant

    July 11, 2018

    Thanks nice video

    Reply
  • dave sugunan

    September 23, 2018

    Thx u. Great video

    Reply
  • FRANCOIS VAN ENGELEN

    October 12, 2018

    Neeeeee niet goed waar is de aarde van de kabel.
    Haal het in godsnaam er van af.(of verander te titel van het filmpje)
    zo moet het dus niet.
    Gebruik een goede knip tang.
    De kabel stripper is ook niks die beschadigd de kabel.

    Reply
  • FRANCOIS VAN ENGELEN

    October 12, 2018

    zo moet het https://www.youtube.com/watch?v=ktQVwfo-s9w

    Reply
  • Amber Adams

    November 12, 2018

    So easy to understand thank you

    Reply
  • PE1BVQ

    November 17, 2018

    Is this movie a joke? No earth connection and isolation to short on inner wire!I never see such an bad vid, see  https://www.youtube.com/watch?v=ktQVwfo-s9w

    Reply
  • SergSpace

    November 21, 2018

    You cut a lot of wire, man, 3:29 which will increase wire impedance, that will invoke overheating in this connection and in the end make a bad signal transmission. This is a Tutorial of how not to do.

    Reply
  • Mario Ramos

    December 7, 2018

    speechless IPC CIT

    Reply
  • pankaj das

    December 13, 2018

    Can you please tell me where I can buy this tools..I am from India..

    Reply
  • Simon Baxter

    January 25, 2019

    Been in the electronics and RF industry for over 35 years an this is TOTALLY THE WRONG way to crimp a BNC connector on coax. Remind me never to use your services! I hope no one ever uses this as a guide … your just asking for major problems. One tip to viewers, the amount you strip back on each of the layer is defined in the datasheet for the BNC connector, which you can download from the web by searching for the part number. The screen is there for a reason. Cutting it back like this negates its purpose (Screening). The crimp setting you use is also defined on the datasheet. This shows a very poorly over crimped ferrule. You need to go and get some instruction yourself before trying to show others … blind, leading the blind comes to mind!

    Reply
  • johnny 71c

    February 23, 2019

    The circular thing is called a ferrule and the shielding should not be twisted but remain uniform around the ferrule oh and the pin should butt up against the inner dielectric insulation

    Reply
  • Joshua A. Kennedy

    July 28, 2019

    How do you change the polarte on the cable?

    Reply
  • ykdickybill

    September 3, 2019

    Very poor video. Keep the screen / braid full length of crimp and not as a pigtail but 360 deg around stem of BNC , makes a much better connection as surface area is increased. Length of dialectric should match the depth of BNC so it butts up to shoulder inside the tube of the BNC. Poor explanation no better than poor DIY standard. Find a better video folks there are plenty on YouTube

    Reply
  • Otunla oluwashina

    September 23, 2019

    thanks

    Reply

Leave a Reply